Udo-Amps Udo Roesner Amps DaCapo 75 Acoustic Guitar Combo
Description
Presenting the all new Udo Roesner Amps DaCapo 75 Acoustic Guitar Combo. Udo Roesner's work with AER is legendary, redefining what can be expected from an acoustic amp. He's now launched a new venture with the help of MARco-Labs to introduce Udo-Amps to the world. The first in this new venture is the all new DaCapo 75. "The DaCapo 75 is a two channel combo amplifier made for music lovers, privates or professionals, that value tone and want their instruments sound as they really do. In all my work in the field of acoustics and musical instruments over the last decades I have been striving to bridge the gap between what we wish for as „natural sound“ and the often modest sounding reality. Technology just plays a limited role - the room, the instrument, the own attitude, the individual idea of sound and even the joy of playing music, everything becomes part of the recipe to feel good and enchant with . With the Da Capo75 you have acquired a wonderful tool, that will help you to perfom magic. What and how you play into it will be played back completely relaxed, with ease and unaltered. The handling is simple, it is clearly structured and it just does what it is supposed to do. Yours musically, Udo Roesner" INPUTS: channel 1 and 2: switchable instrument or microphone input as combi-socket, XLR + jack ¼” (6.35 mm) and clip indicators, min. dynamic headroom: 8 dB line mode: high impedance jack input for instruments (pick-ups directly), unbalanced and line-level sources impedance: 2.2 Meg sensitivity: 22 mV (–33 dBV) (high/low attenuator: –10 dB via jumper) equivalent input noise: A-weighted: 1 uV (–120 dBV) mic mode: XLR- , balanced and stereo jack socket, unbalanced impedance: XLR, balanced: 1.2 kOhm impedance: jack, unbalanced: 2.7 kOhm sensitivity: 3.3 mV (–50 dBV) voice filter: –10 dB at 270 Hz (referred to 10 kHz) equivalent input noise: A-weighted: 0.8 uV (–122 dBV) phantom power: (XLR only): 48 V, max. 10 mA, short-circuit protected return: unbalanced jack input, ¼” (6.35 mm), pre-master sensitivity: 320 mV (–10 dBV) impedance: 19.7 kOhm (note: impedance changes to 4.7 kOhm when external effect is switched OFF) aux in: TRS stereo input, 3.5mm OUTPUTS: phones: headphones, jack socket, stereo, L/R connected, ¼” (6.35 mm) input Impedance: 470 Ohm (common for L and R) (!) Please note: Use TRS (Stereo Jacks) only. Does not work with mono jacks, and When plugged in, internal speaker is muted! send: jack socket, unbalanced, ¼” (6.35 mm), pre master, output voltage: 1.4 V (+3 dBV) line out 1 and 2: jack socket, unbalanced, preamp out, ¼” (6.35 mm), post effect, post EQ and master output voltage 2: 1.74 V (+3 dBV) output voltage 1: 0.33 V (-4.6 dBV) DI-out 1 and 2: balanced XLR socket, pre/post EQ (sitchable by jumper) post effect and master 1 = ground 2 = positive 3 = negative differential output voltage: 140 mV (–17 dBV) FOOTSWITCH footswitch: TRS jack socket ¼” (6.35 mm) to connect latching dual foot switch. tip = built-in effect on/off, ring = parameter adjust or additional effect on/off , sleeve = common (ground) (!) Please note: Effect is OFF when the footswitch is ON. EQ - Tone Controls channel 1: tone: –3 dB at 700 Hz, +7 dB at 8 kHz bass: 8 dB at 100 Hz (shelf type) middle: 6 dB at 800 Hz treble: 8 dB at 10 kHz (shelf type) channel 2: hpf filter: 40Hz to 350 Hz, bass: 8 dB at 100 Hz (shelf type) middle: 6 dB at 800 Hz treble: 8 dB at 10 kHz (shelf type) EFFECTS effect presets: 1: reverb long, 2: reverb short, 3: chorus, 4: custom delay, 5: my delay, 6: tap n’ delay, external effect: parallel effect loop (see also send and return) efx pan: blends both internal and external effects between channels 1 and 2, POWER SECTION power amp: 75 W / 4 ohm, DMOS, monolithic I.C. dynamic range, A-weighted: 92 dB analog signal processing: dedicated equalizer, subsonic filter, adaptive peak limiter limiter threshold: 60 W speaker system: 8” (200 mm) twin cone full-range speaker, bass reflex enclosure mains power: mains voltage (depending on model): 100, 120, 230, or 240 V AC, 50–60 Hz power consumption: max. 200 W mains fuse: 5 x 20 mm T 1A L /250 V for 230 and 240 V 5 x 20 mm T 2A L /250 V for 100 and 120 V GENERAL cabinet: 12 mm (0.47”) plywood finish: polyester black spatter finish dim: 265 mm (10.43“) height, 325 mm (12.8“) width, 245 mm (9.65“) depth weight, net: 7.5 kg (16.5 lbs) 13