3rd Power Amplification 3rd Power DRGN 4x12 Cabinet in Black

Presenting the 3rd Power DRGN 4x12 Cabinet made to match the DRGN 100 Watt head. The DG412 is designed to capture the enormous spirit and sonic footprint of a full-on wet/dry/wet rig, while packing it into a single streamlined enclosure. Crafted from 5/8″ birch, the DS412 features 3rd Power's legendary embedded triangular speaker chambers to eliminate standing waves and internal reflections. With construction features including isolated speaker chambers (one open, three closed) and a tuned triangle port, the DG412 delivers your full frequency response with a detail and punch that sounds like a mastered record and won’t get lost in the mix. While the DG412 cab is 4-channel sound capable, it also delivers a monstrous mono 412 performance. This custom cabinet offers maximum setup flexibility, making easy work of wet/dry/wet, X-pattern, dual 212, stereo 212 (vertical or horizontal) configurations – all within the footprint of a single 412 cabinet. Features include: • Internal triangular speaker chamber design eliminates standing waves • 16-ohm Mono or… • Dual 8-ohm Stereo or… • 8-ohm 212 plus two 16-ohm Stereo FX (wet/dry/wet) • 5/8″ baltic birch enclosure construction • Closed-back upper chambers, single open-back chamber on the bottom It Features 4 Speaker Chambers, Loaded with 2x Celestion G12T-75 and 2x ToneSpeak Manchester 1290 speakers, and has a Cast and Polished 3D Dragon Emblem. Mono, Stereo, and Wet/Dry/Wet Operating Modes W/D/W, Mono, Stereo, X-pattern, 4 Channel Operating Modes X-pattern operation is totally possible. Each speaker is addressable individually, as a 412, as two separate 212s (vertical or horizontal), or in the wet/dry/wet configuration. Suggested Wet/Dry/Wet rig setup: Your dry head runs the bottom two speakers as a mono 212. Your main amp will drive the stereo FX processor. The stereo wet output from your processor will feed a stereo power amp (not included). The power amp drives the top two speakers in stereo for you wet effects sound. 3rd Power recommends the dry signal be placed on the bottom as it keeps the sonic blast from blowing into the lead or BG vox on stage. Low end coupling from the stage/studio floor is usually a benefit as well. Effects are spatial enhancement and they’re going to be more effective positioned higher. Stereo spread will be more noticeable as well. Patch-bay Configurations Jack #1: 16 ohm mono cab Jack #2: 8 ohm top two speakers in mono only Jack #3: 16 ohm top right speaker only Jack #2 and #3: top speakers 16 ohms each in stereo Jack #4: 8 ohm bottom two speakers in mono only Jack #5: 16 ohm bottom right speaker only Jack #4 and #5: bottom speakers 16 ohms each in stereo Jack #2 and #4: 8 ohms top two speakers in mono, 8 ohms bottom two speakers in mono Jack #4, #2 and #3: 8 ohms mono bottom speakers, 16 ohms each top stereo speakers for WDW NOTE: To run stereo L&R only, you will need two separate amplifiers. Using the 2x 8 ohm jacks on the back of amp one, plug each into jacks #2 and #4. On amp two, again using the 2x 8 ohm jacks, plug each one into jacks #3 and #5. In essence, you’re addressing the separate speaker chambers as if they were individual cabinets. Model Name: DG412 Speakers Installed Top Two Drivers: Celestion G12T-75 (16 Ohms Each) Bottom Two Drivers: Tone Speak Manchester 1290 (16 Ohms Each) Power Handling Mono 412 Mode: 330 Watts Stereo 212 Mode: 165 Watts Per Channel Single Driver Mode Celestion G12T-75: 75 Watts Each Single Driver Mode Tone Speaker Manchester 1290: 90 Watts Each Impedance Mono Mode: 16 Ohms Stereo Mode: 8 Ohms Per Channel Three Channel Sound: 8 Ohms Mono (212), 16 Ohm 2 Channel FX in Stereo Quad Mode: 16 Ohms Discreet Country of Manufacture: Designed and built in USA Case Composition: 5/8″ birch enclosure, dado joinery throughout Dimensions (LxWxD): 30” x 30” x 14” Weight: ~90 lbs loaded (~55 lbs unloaded)